• Canopy and Motor Mount for Zagi 400X

    $12.00

    Zagi 400X (not 400) canopy and motor mount.

    Includes hook-and-loop tape and zip ties.

  • Elevons

    $6.00
  • Motor Mount for Zagi HP and HP60

    $10.00

    Motor mount (without canopy), as included with Zagi HP and HP60 models.

    The HP (hard point) flying wing motor mount system integrates a laser cut 1/8″ plywood motor mount laminated inside in the styrene motor tray. This mount system is stable and strong. The HP Tray will accommodate an inrunner motor or a front mounted outrunner motor, up to 30mm diameter. The HP mount has three different pre-measured hole patterns for most motors including the standard Zagi 3100 Kv inrunner.

    No available in .060″ Styrene and black .060″ Kydex.

  • Propeller Adapter

    $6.00

    Prop adapter for Zagi propellers and our brushless motor.

  • Propellers

    $5.00

    Two carbon 5×5 propellers.

    This spoon shaped 5X5 prop was tested against four major 5X5 brands on the Zagi with a radar speed gun. The test was performed in level flight, on the same Zagi, on the same day, in the same conditions just minutes apart. The pilot was not told which prop was on the Zagi and was not told the radar results. The Zagi was landed and a NASCAR style prop and battery change were done. The procedure was repeated three times. The Zagi carbon prop tested 10 to 15 MPH faster than the other four. Since the test was not done to find the best performance in a tractor configuration the only conclusion for the performance difference is that the spoon shaped prop works better in the pusher configuration. The performance difference is perhaps that the wider spoon shape works better in dirty (turbulated) air.

  • Propellers with Adapter

    $10.00

    Two carbon 5×5 propellers with machined aluminum propeller adapter for 3.17mm motor shafts.

    This spoon shaped 5X5 prop was tested against four major 5X5 brands on the Zagi with a radar speed gun. The test was performed in level flight, on the same Zagi, on the same day, in the same conditions just minutes apart. The pilot was not told which prop was on the Zagi and was not told the radar results. The Zagi was landed and a NASCAR style prop and battery change were done. The procedure was repeated three times. The Zagi carbon prop tested 10 to 15 MPH faster than the other four. Since the test was not done to find the best performance in a tractor configuration the only conclusion for the performance difference is that the spoon shaped prop works better in the pusher configuration. The performance difference is perhaps that the wider spoon shape works better in dirty (turbulated) air.

  • Winglets – Lightweight for THL

    $1.00

    Set of two lightweight winglets, as included with each Zagi THL kit.

  • Winglets – Plastic for HP and 5C

    $1.00

    Set of two plastic winglets, as included with each Zagi HP, HP60 and 5C kit. Currently, we only stock white.

  • carbon fiber elevonscarbon fiber elevons

    Carbon Elevons for Zagi HP

    $18.00$27.00

    Here they are! We’ve finally found someone to make Carbon Fiber elevons for us! You’ll get a pair in your order. These are balsa core and precut to fit the HP. Not cheap vinyl carbon sticker material or dyed fiberglass, these are light, rigid and ready to fly. You’ll need more hinge tape to install.

  • Sale!

    Zagi Zijji 6061-T6 Aluminum Motor Mount for Inrunner Motors

    $40.00 $20.00

    This motor mount is abrasive water-jet cut from 6061-T6 aluminum.

    The Zijji mount is shaped with an offset to extend the distance between the prop and the mount. This improves the efficiency of the prop and reduces the noise produced by the prop.

    These are available in inrunner and outrunner configuration and are adaptable to the HP and HP60. Please leave a note in your order.